Compare Prices

Roughing Finishing

Roughing Finishing - Niagara Cutter N85440 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 2 Flutes, 2
Niagara Cutter N85440 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 2 Flutes, 2" Overall Length, 0.250" Cutting Diameter, 0.250" Shank

Roughing Finishing

The Niagara Cutter C230 TiAlN-coated carbide square nose end mill has two flutes and a 30-degree helix angle for general-purpose machining on a range of materials. The tool’s square end has straight cutting edges that create sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The TiAlN coating resists heat better than TiN and TiCN coatings, increasing tool life and performance. It also offers increased hardness for abrasion resistance and may reduce the need for lubricants based on the application. (TiAlN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. Cutting diameter tolerance is +0.000” to...

  • Brand: Niagara Cutter
  • ASIN: B003BIESRY
  • UPC: 698036854409
Roughing Finishing - Niagara Cutter N61656 Carbide Square Nose End Mill, Inch, TiCN Finish, Roughing and Finishing Cut, 45 Degree Helix, 3 Flutes, 4
Niagara Cutter N61656 Carbide Square Nose End Mill, Inch, TiCN Finish, Roughing and Finishing Cut, 45 Degree Helix, 3 Flutes, 4" Overall Length, 0.500" Cutting Diameter, 0.500" Shank

Roughing Finishing

Niagara Cutter’s A345 series TiCN-coated carbide square nose end mill has three flutes and a 45-degree helix angle, making it suitable for high-performance cuts on aluminum and other nonferrous materials. The 45-degree helix provides increased cutting action and chip evacuation compared to end mills with lower helix angles, as it moves excess material quickly up the spiral and away from the workpiece. The end mill’s three flutes provide better chip-carrying capacity than four flutes and a finer finish than two. They efficiently remove excess material from the cutting area and provide a third cutting edge to create an improved finish that may eliminate the need for a second finishing cut in some applications. The center-cutting design has cutting teeth at the end of the tool, so it can be fed straight into the workpiece like a drill bit. The tool’s square end creates sharp, unrounded cuts. The rounded area behind the cutting edge, called the cylindrical land, minimizes tool vibration when machining nonferrous materials. This end mill is best suited for peripheral milling applications. The TiCN coating offers the hardness and abrasion resistance required to machine aluminum and other nonferrous materials, providing more abrasion resistance than TiN coating. The carbide sub...

  • Brand: Niagara Cutter
  • ASIN: B0006TSF3E
  • UPC: 698036616564
Roughing Finishing - Niagara Cutter N68625 Carbide Square Nose End Mill, Inch, AlCrN Finish, Roughing and Finishing Cut, Non-Center Cutting, 5 Flutes, 2.5
Niagara Cutter N68625 Carbide Square Nose End Mill, Inch, AlCrN Finish, Roughing and Finishing Cut, Non-Center Cutting, 5 Flutes, 2.5" Overall Length, 0.250" Cutting Diameter, 0.250" Shank

Roughing Finishing

The Niagara Cutter STS540 Stabilizer AlCrN-coated carbide square nose end mill with five flutes features the patented Stabilizer flute design, which combines variable helix angles and unevenly spaced flutes of differing lengths to allow deeper cuts at higher speeds on hard materials such as steels, stainless steels, and high-temperature alloys. The helix angle varies from tooth to tooth to reduce tool vibration and provide efficient chip removal. The unequal length and spacing of the flutes creates an out-of-phase cutting action that further reduces tool vibration and extends tool life. Five flutes produce a better finish than fewer flutes and allow for higher feed rates compared to the four-flute Stabilizer, depending on the type of material being milled and the cutting depth. Aluminum chromium nitride (AlCrN) coating provides good hardness and better resistance to chemical breakdown in high-heat applications than TiAlN, TiCN, and TiN coatings. The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and hot temperatures, providing longer tool life. The Stabilizer flute geometry, carbide substrate, and AlCrN coating make the STS540 suitable for machining the hard steels, stainless steels, and high-temperature alloys used in in...

  • Brand: Niagara Cutter
  • ASIN: B003D7LEFM
  • UPC: 698036686253
Roughing Finishing - Niagara Cutter N86030 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 3 Flutes, 4
Niagara Cutter N86030 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 3 Flutes, 4" Overall Length, 0.750" Cutting Diameter, 0.750" Shank

Roughing Finishing

The Niagara Cutter C330 TiAlN-coated carbide square nose end mill has three flutes and a 30-degree helix angle for general-purpose machining on a range of materials. The tool’s square end creates sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The end mill’s three flutes provide better chip-carrying capacity than four flutes and a finer finish than two. They efficiently remove excess material from the cutting area and provide a third cutting edge to create an improved finish that may eliminate the need for a second finishing cut in some applications. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The TiAlN coating resists heat better than TiN and TiCN coatings, increasing tool life and performance. It also offers increased hardness for abrasion resistance and may reduce the need for lubricants based on the application. (TiAlN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at ...

  • Brand: Niagara Cutter
  • ASIN: B003BIEV9O
  • UPC: 698036860301
Roughing Finishing - Niagara Cutter N89977 Carbide Ball Nose End Mill, Stub Length, TiAlN Finish, Roughing and Finishing Cutting, 30-Degree, 4-Flute, 2.5
Niagara Cutter N89977 Carbide Ball Nose End Mill, Stub Length, TiAlN Finish, Roughing and Finishing Cutting, 30-Degree, 4-Flute, 2.5" Overall Length, 0.375" Cut Diameter, 0.375" Shank

Roughing Finishing

The Niagara Cutter CSDB430 TiAlN-coated carbide double-end ball nose end mill with stub length has four flutes for a fine finish and a 30-degree helix angle for general-purpose applications. Four flutes produce a better finish than fewer flutes. The stub length increases tool strength and makes it less likely to break in the material being machined. It is best used when depth of cut is shallow. The double-end design has cutting edges on both ends, allowing a new cutting surface to be substituted when the first shows wear, which doubles the tool’s life compared to single-end ball nose end mills. The TiAlN coating resists heat better than TiN and TiCN coatings, increasing tool life and performance. It also offers increased hardness for abrasion resistance and may reduce the need for lubricants based on the application. (TiAlN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. The tool’s ball nose creates contoured surfaces where sharp corners are not required. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bi...

  • Brand: Niagara Cutter
  • ASIN: B003CYKMVS
  • UPC: 698036899776
Roughing Finishing - Niagara Cutter N46412 Carbide Square Nose End Mill, Metric, AlTiN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 39mm Overall Length, 1mm Cutting Diameter, 3.000mm Shank Diameter
Niagara Cutter N46412 Carbide Square Nose End Mill, Metric, AlTiN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 39mm Overall Length, 1mm Cutting Diameter, 3.000mm Shank

Roughing Finishing

The Niagara Cutter C430M metric AlTiN-coated carbide square nose end mill has four flutes and a 30-degree helix angle for general-purpose machining on a range of materials. Four flutes produce a better finish than fewer flutes. The tool’s square end creates sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The AlTiN coating resists heat better than TiN, TiAlN, and TiCN coatings, increasing tool life and performance. It also offers increased hardness compared to TiN and may reduce the need for lubricants based on the application. (AlTiN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. Cutting diameter tolerance is +0.000 mm to -0.050 mm. The round shank accommodates a variety of holders. End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cu...

  • Brand: Niagara Cutter
  • ASIN: B003CYKGB4
  • UPC: 698036464127
Roughing Finishing - Niagara Cutter N85606 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 2.75
Niagara Cutter N85606 Carbide Square Nose End Mill, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 2.75" Overall Length, 0.438" Cutting Diameter, 0.438" Shank

Roughing Finishing

The Niagara Cutter C430 TiAlN-coated carbide square nose end mill has four flutes and a 30-degree helix angle for general-purpose machining on a range of materials. The tool’s square end creates sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. Four flutes produce a better finish than fewer flutes. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The TiAlN coating resists heat better than TiN and TiCN coatings, increasing tool life and performance. It also offers increased hardness for abrasion resistance and may reduce the need for lubricants based on the application. (TiAlN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. Cutting diameter tolerance is +0.000” to -0.002”. The round shank accommodates a variety of holders. End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting e...

  • Brand: Niagara Cutter
  • ASIN: B003CYKFRO
  • UPC: 698036856069
Roughing Finishing - Niagara Cutter N89901 Carbide Square Nose End Mill, Double End, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3
Niagara Cutter N89901 Carbide Square Nose End Mill, Double End, Inch, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3" Overall Length, 0.500" Cutting Diameter, 0.500" Shank

Roughing Finishing

The Niagara Cutter CSD430 TiAlN-coated carbide double-end square nose end mill with stub length has four flutes and a 30-degree helix angle for general-purpose applications. Four flutes produce a better finish than fewer flutes. The stub length increases tool strength and makes it less likely to break in the material being machined. It is best used when depth of cut is shallow. The double-end design has cutting edges on both ends, allowing a new cutting surface to be substituted when the first shows wear, which doubles the tool’s life compared to single-end square nose end mills. The TiAlN coating resists heat better than TiN and TiCN coatings, increasing tool life and performance. It also offers increased hardness for abrasion resistance and may reduce the need for lubricants based on the application. (TiAlN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. The tool’s square end creates sharp, unrounded cuts. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The 30-degree helix angle supports general-purp...

  • Brand: Niagara Cutter
  • ASIN: B003CYKLKU
  • UPC: 698036899011
Roughing Finishing - WIDIA Hanita I2S0188T075L VariMill I2S GP Roughing/Finishing End Mill, 0.75
WIDIA Hanita I2S0188T075L VariMill I2S GP Roughing/Finishing End Mill, 0.75" LOC, 0.1875" Cutting Dia, Carbide, TiAlN Coating, RH Cut,

Roughing Finishing

VariMill GP offers plunging, slotting, and profiling for a wide range of materials and applications. Designed to provide high metal removal rates and excellent surface conditions at a value price. Special proprietary carbide substrates and state-of-the-art surface technology, combined with unique geometries, provides end users with the capability to significantly reduce machining time with heavier and deeper cuts, fewer passes, and faster surface speed. WIDIA geometries are uniquely formed and fine-tuned to optimized chip form, size, and evacuation generated by a given workpiece material.

  • Brand: WIDIA
  • ASIN: B01M3UYUPY

Roughing Finishing I409 Search Results

Looking for more Roughing Finishing similar ideas? Try to explore these searches: Crystal Stones Pierced Earrings, 2002 Ford Explorer Sport Auto, and Marina Naturals.

Roughing Finishing - Popular Video Reviews



365dealnet.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or one of its affiliates.